EXPERIMENTAL STUDY OF OBSERVABLE DEFORMATION PROCESS IN FAULT META-INSTABILITY STATE BEFORE EARTHQUAKE GENERATION

According to the steady state of fault and energy balance, we provided a new idea to observe the precursors for a stressed fault. The meta-instability (or sub-instability) state of a fault is defined as the transition phase from peak stress to critical stress of fast instability (earthquake generation) during a full period of slow loading and fast unloading. The accumulative deformation energy begins to release in this stage. Identifying its deformation before fast instability would be beneficial to obtain premonitory information, and to evaluate the seismic risks of tectonic regions. In this study, we emphasized to analyze deformation process of the meta-instable stage with stain tensor data from a straight precut fault in granite at a slow loading rate, and observed the tempo-spatial features during the full deformation process of the fault. Two types of tectonic zones and instabilities occur on the stick-slip fault. The low- and high-value segments in the volume strain component appear along the fault strike with a load increment. The former first weakens and then becomes initial energy release segments; the latter forms strong stress-interlocking areas and finally turns into the initial region of fast instability. And there are two stages in the entire instable process of the fault: the initial stage is associated with the release of the low volume strain segments, which means fault pre-slips, slow earthquakes or weak earthquakes. The second one characterizes a strong earthquake through the release of high volume strain parts. The rupture acceleration in the first stage promotes the generation of the second. Moreover, fault instability contains two types of strain adjustments along the fault: the front-like strain change along the transition segments from low- to high- strain portions with volume strain release, and the compressive strain pulse of fault instability after the volume strain release extends to a certain range with loading increment. In laboratory experiments, the front-type strain occurs about 12 seconds before fast fault instability; the compressive pulse initiates within less than 0.1 second, and then the fault turns quickly into a dynamic strain adjustment, which appears quasi-synchronously between different measurement points, and, finally, an earthquake is generated.

1. Aochi H., Fukuyama E., 2002. Three-Dimensional Nonplanar Simulation of the 1992 Landers Earthquake. Journal of Geophysical Research: Solid Earth 107 (B2), 2035. https://doi.org/10.1029/2000JB000061.

2. Ben-David O., Cohen G., Fineberg J., 2010. The Dynamics of the Onset of Frictional Slip. Science 330 (6001), 211–214. https://doi.org/10.1126/science.1194777.

3. Brace W.F., Byerlee J.D., 1966. Stick-Slip as a Mechanism for Earthquakes. Science 153 (3739), 900–992. https://doi.org/10.1126/science.153.3739.990.

4. Brace W.F., Byerlee J.D., 1970. California Earthquake: Why Only Shallow Focus? Science 168 (3939), 1573–1575. https://doi.org/10.1126/science.168.3939.1573.

5. Byerlee J.D., 1967. Frictional Characteristics of Granite under High Confining Pressure. Journal of Geophysical Research 72 (14), 3639–3648. https://doi.org/10.1029/JZ072i014p03639.

6. Byerlee J.D., 1978. Friction of Rocks. Pure and Applied Geophysics 116, 615–626. https://doi.org/10.1007/978-3-0348-7182-2_4.

7. Chang J.C., Lockner D.A., Reches Z., 2012. Rapid Acceleration Leads to Rapid Weakening in Earthquake-Like Laboratory Experiments. Science 338, 101–105. https://doi.org/10.1126/science.1221195.

8. Dieterich J.H., 1978. Time Dependent Friction and the Mechanics of Stick-Slip. Pure and Applied Geophysics 116, 790–806. https://doi.org/10.1007/978-3-0348-7182-2_15.

9. Dieterich J.H., 1979. Modeling of Rock Friction: 1. Experimental Results and Constitutive Equations. Journal of Geophysical Research: Solid Earth 84 (В5), 2161–2168. https://doi.org/10.1029/JB084iB05p02161.

10. Dieterich J.H., 1986. Model for the Nucleation of Earthquake Slip. In: Sh. Das, J. Boatwright, Ch.H. Scholz (Eds) Earthquake Source Mechanics. American Geophysical Union 37 (6). https://doi.org/10.1029/GM037p0037.

11. Dieterich J.H., 1992. Earthquake Nucleation of Faults with Rate and State Dependent Strength. Tectonophysics 211 (1–4), 115–134. https://doi.org/10.1016/0040-1951(92)90055-B.

12. Dieterich J.H., Richards-Dinger K.B., 2010. Earthquake Recurrence in Simulated Fault Systems. In: M.K. Savage, D.A. Rhoades, E.G.C. Smith, M.C. Gerstenberger, D. Vere-Jones (Eds), Seismogenesis and Earthquake Forecasting: The Frank Evison, Vol. II, 223–250. https://doi.org/10.1007/978-3-0346-0500-7_15.

13. Dieterich J.H., Smith D.E., 2009. Nonplanar Faults: Mechanics of Slip and Off-Fault Damage. Pure and Applied Geophysics 166 (10), 1799–1815. https://doi.org/10.1007/978-3-0346-0138-2_12.

14. Ellsworth W.L., Beroza G.C., 1995. Seismic Evidence for an Earthquake Nucleation Phase. Science 268, 851–855. https://doi.org/10.1126/science.268.5212.851.

15. Fukuyama E., 2009. Fault-Zone Properties and Earthquake Rupture Dynamics. International Geophysics 94, 1–13. https://doi.org/10.1016/S0074-6142(08)00001-6.

16. He Changrong, 2000. Numerical Simulation of Earthquake Nucleation and Precursory Process in Slipping Fault Planes. Earthquake Research in China 16 (1), 1–13 (in Chinese). He Changrong, 2003. The Interaction of a Double Slider System under Rate- and State-Dependent Friction Law. Science in China (Series D) 33 (Suppl.), 53–59 (in Chinese). He Chang-Rong, Tao Qing-Feng, Wang Ze-Li, 2004. Frictional Strength and Rate Dependence of Gouge under Elevated Temperature and Pressure. Seismology and Geology 26 (3), 450–459 (in Chinese).

17. He Changrong, Wang Zeli, Yao Wenming, 2007. Frictional Sliding of Gabbro Gouge under Hydrothermal Conditions Tectonophysics 445 (3–4), 353–362. https://doi.org/10.1016/j.tecto.2007.09.008.

18. He Changrong, Yao Wenming, Wang Zeli et al., 2006. Strength and Stability of Frictional Sliding of Gabbro Gouge at Elevated Temperatures. Tectonophysics 427 (1–4), 217– 229. https://doi.org/10.1016/j.tecto.2006.05.023.

19. Heaton T.H., 1990. Evidence for and Implications of SelfHealing Pulses of Slip in Earthquake Rupture. Physics of the Earth and Planetary Interiors 64 (1), 1–20. https://doi.org/10.1016/0031-9201(90)90002-F.

20. Hirose T., Shimamoto T., 2005. Slip-Weakening Distance of Faults during Frictional Melting as Inferred from Experimental and Natural Pseudotachylytes. Bulletin of the Seismological Society of America 95 (5), 1666–1673. https://doi.org/10.1785/0120040131.

21. Ikuta R., Satomura M., Fujita A. et al., 2012. A Small Persistent Locked Area Associated with the 2011 Mw 9.0 TohokuOki Earthquake Deduced from GPS Data. Journal of Geophysical Research: Solid Earth 117, B11408. https://doi.org/10.1029/2012JB009335.

22. Kato N., 2012. Dependence of Earthquake Stress Drop on Critical Slip-Weakening Distance. Journal of Geophysical Research: Solid Earth 117, B01301. https://doi.org/10.1029/2011JB008359.

23. Liu Liqiang, Lei Xinglin, 2003. An Observation System of Acoustic Emission Signal Based on Ultra High Speed Parallel Network. Seismology and Geology 25 (3), 477–479 (in Chinese).

24. Liu Peixun, Liu Liqiang, Huang Yuanmin et al., 2009. Robust Arithmetic for Acoustic Emission Location. Chinese Journal of Rock Mechanics and Engineering 28 (S1), 2760– 2764 (in Chinese).

25. Ma Jin, 2016. On «Whether Earthquake Precursors Help for Prediction Do Exist». Chinese Science Bulletin 61 (4–5), 409–414 (in Chinese). https://doi.org/10.1360/N972015-01239.

26. Ma J., Guo Y., Sherman S.I., 2014. Accelerated Synergism along a Fault: A Possible Indicator for an Impending Major Earthquake. Geodynamics & Tectonophysics 5 (2), 387–399. https://doi.org/10.5800/GT-2014-5-2-0134.

27. Ma J., Sherman S.I., Guo Y.S., 2012. Identification of MetaInstable Stress State Based on Experimental Study of Evolution of the Temperature Field during Stick-Slip Instability on a 5° Bending Fault. Science China Earth Sciences 55, 869– 881. https://doi.org/10.1007/s11430-012-4423-2.

28. Ma Shengli, Liu Liqiang, Ma Jin et al., 2003. An Experimental Study on the Nucleation Process of Instable Slip for Homogenous and Heterogeneous Fault. Science in China (Series D) 33 (Suppl.), 45–52 (in Chinese).

29. Ma Shengli, Ma Jin, Liu Liqiang, 2002. Experimental Evidence for Earthquake Nucleation Phase. Chinese Science Bulletin 47 (5), 387–391 (in Chinese).

30. Moore D.E., Rymer M.J., 2007. Talc-Bearing Serpentinite and the Creeping Section of the San Andreas Fault. Nature 448, 795–797. https://doi.org/10.1038/nature06064.

31. Ohnaka M., 1992. Earthquake Source Nucleation: A Physical Model for Short-Term Precursors. Tectonophysics 211 (1–4), 149–178. https://doi.org/10.1016/0040-1951(92)90057-D.

32. Ohnaka M., Akatsu M., Mochizuki H. et al., 1997. A Constitutive Law for the Shear Failure of Rock under Lithospheric Conditions. Tectonophysics 277 (1–3), 1–27. https://doi.org/10.1016/S0040-1951(97)00075-9.

33. Ohnaka M., Kuwahara Y., 1990. Characteristic Feature of Local Breakdown near a Crack-Tip in the Transition Zone from Nucleation to Unstable Rupture during Stick-Slip Shear Failure. Tectonophysics 175 (1–3), 197–220. https://doi.org/10.1016/0040-1951(90)90138-X.

34. Ohnaka M., Kuwahara Y., Yamamoto K., 1987. Constitutive Relation between Dynamic Physical Parameters near a Tip of the Propagating Slip Zone during Stick-Slip Shear Failure. Tectonophysics 144 (1–3), 109–125. https://doi.org/10.1016/0040-1951(87)90011-4.

35. Peselnic L., Dieterich J.H., Mjachkin V.I., Sobolev G.A., 1976. Variation of compressional velocities in simulated fault gouge under normal and direct shear stress. Geophysical Research Letters 3 (7), 369–372. https://doi.org/10.1029/GL003i007p00369.

36. Rebetskii Yu. L., Lementueva R.A., D’yaur et al., 2005. Subordination of Misrostructure Deformations and Brittle Macrodestruction. Doklady Earth Sciences 403 (5), 812–815. Reches Z., Lockner D.A., 2010. Fault Weakening and Earthquake Instability by Powder Lubrication. Nature 467, 452– 455. https://doi.org/10.1038/nature09348.

37. Ren Y.-Q., Liu P.-X., Ma J. et al., 2013. An Experimental Study on Evolution of the Thermal Field of En Echelon Faults during the Meta-Instability Stage. Chinese Journal of Geophysics 56 (5), 612–622. https://doi.org/10.1002/cjg2.20057.

38. Rice J.R., 2006. Heating and Weakening of Faults during Earthquake Slip. Journal of Geophysical Research: Solid Earth 111, B05311. https://doi.org/10.1029/2005JB004006.

39. Rice J.R., Ruina A.L, 1983. Stability of Steady Frictional Slipping. Journal of Applied Mechanics 50 (2), 343–349. https://doi.org/10.1115/1.3167042.

40. Ruina A.L., 1983. Slip Instability and State Variable Friction Laws. Journal of Geophysical Research: Solid Earth 88 (В12), 10359–10370. https://doi.org/10.1029/JB088iB12p10359.

41. Scholz C.H., 1988. The Critical Distance for Seismic Faulting. Nature 336, 761–763. https://doi.org/10.1038/336761a0.

42. Zhuo Y.Q., Guo Y.S., Ji Y.T. et al., 2013. Slip Synergism of Planar Strike-Slip Fault during Meta-Instable State: Experimental Research Based on Digital Image Correlation Analysis. Science China: Earth Sciences 56, 1881–1887. https://doi.org/10.1007/s11430-013-4623-4.

43. Zhuo Y.S., He C.R., 2009. The Rheological Structures of Crust and Mechanics of High-Angle Reverse Fault Slip for Wenchuan Ms8.0 Earthquake. Chinese Journal of Geophysics 52 (2), 474–484 (in Chinese).

44. Zhuo Y.Q., Ma J., Guo Y.S. et al., 2015. Identification of the Meta-Instability Stage via Synergy of Fault Displacement: An Experimental Study Based on the Digital Image Correlation Method. Physics and Chemistry of the Earth, Parts A/B/C 85–86, 216–224. https://doi.org/10.1016/j.pce.2015.03.002.